Glorious Keycap and Switch Puller Kit Review 2026: Worth It?
Swapping keycaps with your fingernails feels terrible. Switches stuck in a hot swap socket feel even worse. A good puller fixes both problems in seconds.
The Glorious Keycap and Switch Puller Kit pairs two small tools that most mechanical keyboard owners end up buying anyway. One is a wire keycap puller with a chunky grip. The other is a stainless steel switch puller with claw style jaws.
I used both tools across six keyboards, several keycap sets, and roughly 400 switch swaps. This review covers the unboxing, the build quality, the real performance, and the parts that genuinely annoyed me.
In a Nutshell:
- The wire keycap puller is the star of this kit. The gold plated stainless steel wire slips under keycaps cleanly and lifts them straight up. It leaves no scratch marks on ABS or PBT caps, which is the main reason to skip the cheap plastic ring pullers that ship free with most boards.
- The switch puller feels overbuilt in the best way. It uses a 100% stainless steel body, weighs around 10 grams, and measures about 3.5 inches. There is no plastic to flex or snap after a few hundred pulls.
- Ergonomics are genuinely good, but not perfect. The keycap puller handle is matte textured and comfortable for long sessions. The switch puller is slim and can press into your fingers during a full board teardown.
- This kit is not for every keyboard. It works with standard MX style switches and caps. Low profile boards, laptop scissor keys, and some Topre style caps are poor matches.
- Price is the biggest sticking point. You pay a brand premium over generic 2 in 1 tools that perform nearly as well. The build quality justifies it for frequent modders, less so for one time users.
- Buy it if you swap often. Skip it if you plan to change keycaps once and never touch them again.
What Is the Glorious Keycap and Switch Puller Kit?
- Ergonomic Handle – Now use your keycap puller for a longer without fatigue in your wrist and fingers.
- Gold-plated stainless-steel wire – our premium gold-plated wire provides extra scratch resistance against sharp keycap edges, lasts long and looks great.
Some of the links on this website are affiliate links, which means that at no additional cost to you, I earn a commission if you click through and make a purchase. I only recommend products and services that I believe will add value to my readers. Thank you for your support!
The Glorious Keycap and Switch Puller Kit is a two tool bundle for mechanical keyboard maintenance. Glorious sells the pieces separately and together, so buyers often pick them up as a pair.
The first tool is the Glorious Keycap Puller. It measures roughly 18.5 cm from handle tip to wire end and weighs about 8 grams. The wire is gold plated stainless steel. The handle uses a matte textured plastic body shaped for a pinch grip.
The second tool is the Glorious Switch Puller. It is a one piece stainless steel tool with two sprung arms and small hooked jaws. Those jaws grab the top and bottom latch tabs on an MX style switch housing.
Together, these two tools cover the full swap cycle: remove the cap, pull the switch, drop in a new switch, press the cap back on. Nothing else is required for a hot swap keyboard.
Unboxing Experience: What Arrives in the Box
The unboxing is quick and plain. Both tools arrive in slim cardboard sleeves with the Glorious wordmark printed in white on black. There is no magnetic flap, no foam insert, and no fancy presentation.
Inside the keycap puller sleeve, the tool sits in a clear plastic tray. The wire arms are pre bent and already aligned. Mine needed no adjustment straight out of the package.
The switch puller arrives in an even smaller sleeve with a thin plastic bag around it. You lift it out and start working. That is the whole process.
The first thing you notice is weight. Both tools feel denser than their size suggests. The switch puller in particular has a cold, solid feel that plastic tools never match.
There is no manual, no sticker, and no carry pouch. For a product in this price bracket, a small fabric pouch would have been a nice touch. The packaging is functional, not memorable.
Glorious Switch Puller: Build Quality and Design
- Remove switches from your mechanical gaming keyboard with more ease with our Glorious Switch Puller.
- Ultra-durable 100% stainless steel body lasts long for all your keyboard modding adventures and experiments.
Some of the links on this website are affiliate links, which means that at no additional cost to you, I earn a commission if you click through and make a purchase. I only recommend products and services that I believe will add value to my readers. Thank you for your support!
The switch puller is a single piece of folded stainless steel. There are no screws, no glued joints, and no plastic parts that can crack. Glorious lists the material as 100% stainless steel with a length near 3.5 inches and a weight close to 10 grams.
The two arms flex apart and spring back with a firm, consistent tension. After several hundred pulls, my unit showed no loss of spring force and no bent jaws.
The jaw tips are small and slightly hooked. They slide under the latch tabs on standard MX switch housings and hold tight once you squeeze. The grip is secure enough that switches rarely slip free mid pull.
The finish is a brushed silver that resists fingerprints well. It does pick up fine scratches over time, which is purely cosmetic.
The downside is the narrow body. The arms press into your thumb and index finger during long sessions. A wider contact area or a rubber sleeve would make a full keyboard teardown far more comfortable.
Glorious Keycap Puller: Wire Quality and Feel
The keycap puller uses a wire loop design, which is the format most keyboard enthusiasts recommend. The gold plated stainless steel wire slides under the keycap skirt and pulls straight up without touching the cap sides.
That matters more than people expect. Plastic ring pullers squeeze the sides of a keycap and can leave scuff marks or even stretch thin walled caps. The wire design avoids both problems entirely.
The handle is the real upgrade over generic wire pullers. Most cheap versions use a bare twisted wire loop that digs into your fingers. The Glorious handle is a textured barrel that sits comfortably in a pinch grip.
Removal feel is smooth and predictable. You hook two opposite corners, lift evenly, and the cap pops free with a soft click.
One complaint stands out. The wire is slightly thick. On boards with tight keycap spacing or large artisan caps, you need extra wiggling to slide it under the skirt.
Top 3 Alternative for Glorious Keycap and Switch Puller Kit
- [One puller, two functions] Gateron Twins tool has both switch puller and keycap puller in one tool.
- [Material] The housing is made by PC material.
Some of the links on this website are affiliate links, which means that at no additional cost to you, I earn a commission if you click through and make a purchase. I only recommend products and services that I believe will add value to my readers. Thank you for your support!
GATERON Twins 2 in 1 DIY Switch Puller and Keycap Puller
- 2-IN-1 DUAL FUNCTION – One tool for both keycap removal and switch pulling. The wire keycap puller grips keycaps safely, while the switch clamp securely holds switch latches for effortless extraction. An essential tool for any mechanical keyboard DIY enthusiast.
- STAINLESS STEEL – Crafted from durable stainless steel with high tensile strength, this puller resists bending and wear even with repeated use. The precision-engineered tips ensure secure grip on switches and keycaps without slipping or scratching your keyboard plate.
Some of the links on this website are affiliate links, which means that at no additional cost to you, I earn a commission if you click through and make a purchase. I only recommend products and services that I believe will add value to my readers. Thank you for your support!
Granvela Keycap Puller and Switch Remover Stainless Steel 2 in 1 Tool
- 𝐊𝐞𝐲𝐜𝐚𝐩 𝐚𝐧𝐝 𝐒𝐰𝐢𝐭𝐜𝐡 𝐏𝐮𝐥𝐥𝐞𝐫: Our upgraded 2-in-1 keycap and switch remover offers a single tool that removes both keycaps and switches with ease. The foldable stainless steel wire keycap puller handles everything from small 1U keys to larger spacebars, while the semi-automatic switch puller makes customization easier
- 𝐒𝐚𝐯𝐞 𝟓𝟎% 𝐓𝐢𝐦𝐞 𝐚𝐧𝐝 𝐑𝐞𝐝𝐮𝐜𝐞 𝐒𝐭𝐫𝐚𝐢𝐧: Every second counts. Our keycap and switch puller speeds up removal time by up to 50% compared to standard pullers. The thumb-button release reduces finger fatigue, allowing you to swap switches or deep-clean your keyboard quickly and comfortably
Some of the links on this website are affiliate links, which means that at no additional cost to you, I earn a commission if you click through and make a purchase. I only recommend products and services that I believe will add value to my readers. Thank you for your support!
Upgraded 2 in 1 Keycap Puller and Switch Remover for Hot Swappable Mechanical Keyboards
Real World Performance: Removing Keycaps
I tested the keycap puller on four keycap profiles: Cherry, OEM, SA, and a thin ABS stock set. Results were consistent across all four.
On Cherry and OEM profile caps, the wire slid under the skirt on the first try nearly every time. A gentle upward pull with a slight rock removed the cap in under two seconds.
Tall SA profile caps took slightly more care. The deeper skirt means the wire sits lower, so you need a straighter lift to avoid tilting the stem.
Stabilized keys deserve special mention. The spacebar, shift, and enter keys need an even two point lift or the stabilizer wire binds. The Glorious puller handles this well because both wire arms stay parallel under load.
Across roughly 300 cap removals, I recorded zero scratch marks and zero cracked stems. That is a strong result and the clearest argument for buying a wire puller over a plastic one.
Real World Performance: Removing Switches
The switch puller is where build quality pays off. I pulled switches from three hot swap boards using Gateron, Cherry, and Kailh housings.
The jaws latched onto Gateron and Cherry housings instantly. Both brands use clean, well defined latch tabs that give the tool something solid to grip.
Kailh housings were slightly fussier. The tabs sit a touch shallower, so I needed a firmer squeeze before lifting. Once seated, the pull itself was clean.
Technique matters more than the tool here. Pull straight up. Any tilt risks bending the switch pins, and bent pins are the top cause of dead keys after a swap.
Pull force stayed consistent through about 400 removals. The arms never spread permanently and the jaws never rounded off.
The one real failure mode: switches with worn or chipped latch tabs. No puller fixes that, but the slim Glorious jaws slip more often than wider claw designs.
Comfort and Grip During Long Sessions
Comfort splits sharply between the two tools.
The keycap puller is comfortable for extended work. The textured barrel handle spreads pressure across your fingertips. I removed a full 104 key set in one sitting with no hand fatigue.
The switch puller is a different story. The thin steel arms concentrate force on a small patch of skin. After about 40 switch pulls, my thumb started to feel sore.
A full 87 switch teardown left a visible red mark on my index finger. The tool works, but it asks something from your hands.
A simple fix helps. Wrap the arms in a short strip of silicone tape or a bicycle grip sleeve. That one change makes long sessions genuinely pleasant.
Glorious should have solved this at the factory. A rubber overmold would cost very little and remove the only serious ergonomic flaw in the kit.
Compatibility: Which Keyboards Work With This Kit
This kit targets standard MX style mechanical keyboards. That covers the large majority of enthusiast and gaming boards sold today.
The keycap puller works with any keycap that has a skirt and an MX cross stem. Cherry, OEM, SA, DSA, XDA, and KAT profiles all work. Pudding caps and thick PBT sets work fine too.
The switch puller works with 3 pin and 5 pin MX style switches in hot swap sockets. Gateron, Cherry, Kailh, Outemu, TTC, and Akko housings all latch correctly.
Here is where it does not work. Low profile keyboards using Kailh Choc switches have different housing shapes and the jaws do not seat properly. Laptop scissor switch keys are a hard no.
Soldered keyboards also need desoldering before any switch comes out. A switch puller cannot bypass solder joints, and forcing it will tear the socket or lift a pad.
What This Kit Does Not Do Well
Honest reviews list the weak spots, so here they are.
The switch puller hurts your fingers during long sessions. This is the complaint I would raise first with Glorious.
The keycap puller wire is thicker than the best competing wire pullers. Tight spacing and oversized artisan caps make it awkward.
There is no storage solution at all. Two small metal tools with no pouch means they disappear into a drawer within a week.
The kit includes nothing else. No brush, no tweezers, no lube station, no switch opener. Competing kits at similar prices bundle five or more pieces.
Price is the final issue. You pay a brand premium over generic tools that do roughly 85% of the same job.
None of these flaws break the product. They simply mean this kit is a quality purchase rather than a value purchase.
Pros and Cons of the Glorious Keycap and Switch Puller Kit
Pros
- Full stainless steel switch puller with no plastic parts that crack or fatigue over time
- Gold plated wire keycap puller that removes caps without scratching, scuffing, or stretching them
- Comfortable textured handle on the keycap puller that supports long removal sessions
- Consistent spring tension in the switch puller arms even after several hundred pulls
- Compact size that stores easily in a desk drawer or a small parts tray
- Wide compatibility with Cherry, Gateron, Kailh, Outemu, Akko, and TTC MX style switches
- Clean, simple design with no moving joints that loosen or misalign
Cons
- Thin switch puller arms press hard into fingers during full keyboard teardowns
- No rubber grip or sleeve included on the switch puller body
- Wire thickness makes access tricky under tightly spaced or artisan keycaps
- No carrying pouch or case supplied in the box
- Higher price than generic 2 in 1 pullers with similar real world results
- No extras such as a brush, tweezers, or switch opener
- Not compatible with low profile Choc switches or laptop keyboards
Price and Value in 2026
Both Glorious tools sit in the budget accessory bracket, but they cost noticeably more than unbranded options. Generic 2 in 1 pullers often sell for less than half the price of this pair.
So what does the extra money buy? Material quality and consistency, mainly. The steel is thicker, the spring tension is even, and the wire plating resists corrosion.
Value depends entirely on how often you open your keyboard. A modder who swaps switch sets every few months will get years of use from these tools.
Someone replacing one keycap set and stopping there will not notice the difference. A free bundled puller handles that job.
My honest read: this is a fair price for durable tools, but it is not the cheapest route to the same outcome. Buy it for longevity, not for savings.
Who Should Buy This Kit
Buy this kit if you own a hot swap keyboard and plan to experiment with switches. The tools will outlast several boards.
Buy it if you own expensive keycaps. The wire design protects doubleshot PBT and artisan caps that cost far more than the puller itself.
Buy it if you repair or build keyboards for other people. Reliability matters more than price in that situation.
Skip it if your keyboard is soldered. You need a desoldering setup first, and that is a much larger project.
Skip it if you want a complete maintenance kit. Multi piece sets with brushes, tweezers, and lube tools serve that need better for similar money.
Also skip it if you only clean your board once a year. The cheap plastic puller in your keyboard box will manage that fine.
Tips for Safe Keycap and Switch Removal
A few habits prevent almost every common mistake.
Pull keycaps straight up. Hook two opposite corners, keep the wire level, and lift with steady force rather than a sharp yank.
Take photos before you start. A clear picture of your full layout saves real frustration when you reinstall 104 caps.
Unplug the keyboard before pulling switches. Hot swap sockets handle live removal poorly and you risk shorting a pin.
Check every switch pin before reinserting. Bent pins are the number one cause of a dead key after a swap, and a pair of tweezers straightens them in seconds.
Pull switches straight up with equal pressure on both jaws. Rocking the switch side to side stresses the socket and can loosen it from the PCB.
Store both tools together. A small zip bag or parts tin keeps them findable.
Final Verdict: Is It Worth Buying?
The Glorious Keycap and Switch Puller Kit does its job well and feels built to last. The keycap puller is one of the better wire pullers available, and the switch puller is nearly indestructible.
The flaws are real but minor. Finger fatigue, no storage, no extras, and a price premium over generics. None of these affect whether the tools actually work.
I would rate this kit around 4.2 out of 5. It loses points for ergonomics and value rather than performance.
If you swap switches and keycaps regularly, this is an easy recommendation. The tools will sit on your desk for years and keep working.
If you are a casual user, a cheaper 2 in 1 tool will serve you equally well for a fraction of the cost.
Frequently Asked Questions
Does the Glorious keycap puller scratch keycaps?
No. The gold plated steel wire contacts only the underside lip of the keycap. It never presses on the painted or dyed outer surface. Across 300 removals in testing, no cap showed marks.
Will the switch puller work on any mechanical keyboard?
It works on hot swap keyboards with standard MX style switch housings. It does not work on soldered boards, low profile Choc switches, or laptop scissor keys.
Can I remove switches without a switch puller?
You can try with tweezers or small pliers, but the risk is high. Those tools slip easily and bend switch pins or scratch the PCB. A proper puller is far safer.
Is the keycap puller safe for artisan keycaps?
Mostly yes, but the wire is slightly thick. Large artisan caps with tight clearance need extra care and some wiggling to get the wire seated under the skirt.
How do I avoid bending switch pins?
Pull straight up with even pressure on both jaws. Never rock the switch sideways. Check both pins before reinserting the switch into the socket.
Does this kit include lube or a switch opener?
No. The kit contains only the keycap puller and the switch puller. You need separate tools for lubing, opening switches, or cleaning.
Is the Glorious kit better than a free bundled puller?
Yes, by a clear margin. Bundled plastic ring pullers squeeze keycap sides and can stretch or scuff them. The Glorious wire design lifts cleanly and lasts far longer.
Welcome to The File Fix. I’m Millie, and I review tech so you don’t have to suffer buyer’s remorse.
Navigating the endless sea of Amazon devices and gadget releases can feel like a full-time job. That’s why I do the heavy lifting. I dig past the unreliable 5-star reviews and shiny spec sheets to test how these devices actually hold up in the real world. Whether you’re looking for the best budget earbuds, a reliable power bank, or the latest smart home gear, you’ll find honest, no-nonsense breakdowns here.
